Graphy · supplied and supported across Canada
+1 437 421 7746
Request a quote
Graphy · Canada

Graphy 3D printing systems for dental practices in Canada

Graphy makes the equipment behind direct-printed aligners: the printer, the shape-memory resin, the post-cure unit and the spinner that finishes them. Bought as a system they replace the thermoforming line entirely. i-VISTAMED supplies, installs and supports the full Graphy range across Canada.

Request a quote
Browse all Graphy products
See the aligner savings calculator
  • Full system — Printer, resin, cure and spinner
  • Installed by us — Commissioning and calibration
  • Trained team — Workflow training included
  • Canada-wide — Shipped and serviced from Ontario

Get pricing for Graphy

Tell us what you are equipping. We reply the same business day.





    We reply the same business day. No obligation.

    Full systemPrinter, resin, cure and spinner
    Installed by usCommissioning and calibration
    Trained teamWorkflow training included
    Canada-wideShipped and serviced from Ontario

    The Graphy system

    Four components that together replace a thermoforming workflow. Available individually or as a complete in-clinic setup.

    3D printer

    The printer at the centre of the workflow, specified for direct-printed aligner production rather than general-purpose modelling.

    View products

    Tera Harz printing material

    Shape-memory resin engineered so the aligner itself is printed, not thermoformed over a model.

    View products

    Tera Harz Cure

    Post-curing unit that finishes printed aligners to their working properties.

    View products

    Tera Harz Spinner

    Removes excess resin before curing — the step that decides surface finish and fit.

    View products

    Why the system, not just the printer

    Printing is one of four steps

    A printer alone does not produce a usable aligner. Spinning, curing and material handling decide fit and finish, which is why the components are specified together.

    No models, no thermoforming

    Direct printing removes the model-printing and pressure-forming stages entirely, along with the trimming and the storage they require.

    Commissioned, not shipped

    We install, calibrate and train on site. Most in-clinic printing that fails, fails at commissioning rather than at purchase.

    Not sure which configuration you need?Send us your operatory setup and we will specify it for you — no obligation.
    Request a quote
    Call +1 437 421 7746

    Where practices usually start

    Testing the workflowStart with the printer, resin and cure unit and run a small number of cases before committing the whole treatment book.
    Full in-clinic productionThe complete four-component system, plus training for the team member who will own the workflow day to day.
    Already printing modelsIf you print models today, direct-printed aligners remove a stage rather than adding one. The savings calculator on our aligner page shows the difference per case.

    From our Graphy articles

    How direct printing works, and what a clinic needs to run it.

    Read the Graphy articles

    Frequently asked questions

    Do I need all four Graphy components?
    For direct-printed aligner production, yes — printing, spinning and curing are one process. Components can be phased in, but a printer on its own will not produce a finished aligner.
    Do you install and train, or just ship the equipment?
    We install, calibrate and train on site. Commissioning is where most in-clinic printing setups succeed or fail.
    What does it cost per case compared with outsourcing?
    That depends on case complexity, step count and how much of the workflow stays in clinic. The savings calculator on our aligner page compares three workflows side by side.
    Can I use the printer for anything other than aligners?
    The system is specified for direct-printed aligner production. Talk to us about your intended use before assuming a second application.
    Is service handled in Canada?
    Yes — installation, parts and support run through i-VISTAMED in Ontario.

    Request pricing for Graphy

    Tell us what you are equipping and we will come back with a configuration and a written quote. If something is not the right fit for your practice, we will say so.





      We reply the same business day. No obligation.